International Stoneworks -- SEAL & GO ENHANCER

2523 Fairway Park Drive
Suite 510 ~ Houston, TX 77092
sales@intlstoneworks.com
(713) 956-8291 ~ 1-800-775-TILE
Fax (713) 956-8293

SEAL & GO®
ENHANCER
SOLVENT BASED-COLOR
ENHANCING IMPREGNATOR-SEALER

Intended Use:
SEAL & GO® ENHANCER S is a color enhancer with superior water and stain protection for all interior and exterior natural stone, marble, granite (flamed and polished), limestone (honed and polished), Travertine (cross-cut and polished), grout and other masonry surfaces.

Benefits of SEAL & GO® ENHANCER S

Enhances Color

Inhibits Efflorescence

Virtually Odorless

Weather Resistant

Interior and Exterior Use

Deep Penetrating Protection

Effective Oil Barrier

Will not add any shine to the stone

Technical Data:
SEAL & GO® ENHANCER S has superior penetration properties due to the low surface tension on the proprietary blend of isoparrafinic hydrocarbon solvents trademarked Penetral (TM).

Physical Properties:

Evaporation rate: 0.26 (n-butyl acetate = 1)

Density: .8 @ 25 degrees C

Flash point: 120 degrees F

Color: clear

Packaging:
Standard packaging with plastic containers of gallons, 5 gallons polyethylene pails.

Shipping:
SEAL & GO® ENHANCER S is shipped as a combustible liquid #UN1256.

DIRECTIONS:

Test in a small inconspicuous area with a 24-hour cure time to determine the ease of application. Allow grout to cure a minimum of 48 hours prior to SEAL & GO® ENHANCER S application. Check to make sure surface is clean and dry. Liberally apply a first coat with a brush, paint roller, or low pressure sprayer. Let penetrate for 10 to 15 minutes. DO NOT LET DRY. Wipe off any excess residue. A minimum of 2 hours later, repeat the procedure. Allow a minimum of 2 hours of drying time between coats.

On a very porous surface, the first coat will soak in considerably. The second coat will cover approximately double the first coat. Apply additional coats as needed. If after drying, a light haze appears, lightly dampen a clean cloth with SEAL & GO® ENHANCER S and wipe surface.

Do not walk on surface for at least 2 hours. Full cure is acheived in 24 hours.

Coverage and Expected Wear:
Depending on type of stone, porosity, texture of surface and method of application:

Coverage (per coat): Approx. 100 to 1000 sq.ft. per gallon If surface is heavily soiled, pre-clean with Zoom. Use Lavenet for routine cleaning.

PRECAUTIONS

This product is combustible and contains petroleum distillates. Use in ventilated areas. Wear organic, vapor respirator, solvent proof gloves, safety goggles and protective clothing. Exposure to high vapor concentration must be avoided. Keep small children and pets out of the area until material has thoroughly dried. Store only closed original container.
Keep out reach of children

Emergency First Aid Procedures
If swallowed:
Do not induce vomiting. Drink large quantities of water. Call physician immediately.
Inhalation:
Relocate to fresh air. If symptoms persist, seek medical attention

REMEMBER
SEAL & GO® sealers are not an absolute impenetrable barrier to all spills, soils or stains. However, natural stone, tile or grout properly sealed with SEAL & GO® sealers will repel stains more effectively and clean more easily when proper cleaning solutions and methods are used. SEAL & GO® sealers do not prevent general soiling nor do they eliminate the need for routine cleaning and proper care of the sealed surface.

In no case will International Stoneworks Inc. be liable for direct, indirect, consequential, economic or other damage. International Stoneworks Inc. will not be responsible for the damage to property or injury to persons due to the improper use or misapplication of SEAL & GO®, SEAL & GO® ENHANCER S, or any other chemicals sold by the company.

Product Page

View MSDS